![]() ![]() I am trying to get a TP-Link Archer A7 V5 to connect to a wireless network that I can see and is an open network. and I guess I should probably start over with my descriptions. so, I think I figured out the issue with the NTP. Last edited by Alozaros on Mon 6:15 edited 2 times in total Stubby DNS over TLS I DNSCrypt v2 by mac913 Netgear R7000 -DD-WRT 54475 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN Netgear R9000 -DD-WRT 54475 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla Netgear R7800 -DD-WRT 54475 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas TP-Link WR1043NDv2 -DD-WRT 54475 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN TP-Link WR1043NDv2 -DD-WRT 54420 Gateway/DoT,Forced DNS,AP Isolation,Ad-Block,Firewall,VPN,x1VLAN Or use an ntp time IP instead or domain name in the NTP box.įor your router use the lower settings 128 bit certĭo not expect performance greater than 10 mbit max NTP time is vital, you can use the default DDWRT ntp time, just select time zone Have a look here, there was a recent discussion about PIA, with a lot of useful info updated Location: UK, London, just across the river. Last edited by egc on Sun 18:40 edited 1 time in total You can use the other radio for connecting clients or make a VAP on the radio connected to the hotspot later.ĭo as the wiki tells you, reset to defaults first and start from scratch You are connecting to a public hotspot so I would advise to use Client mode see: So the first thing to do is to get your setup working That is why the forum guide lines ask you to give as much information as you can like network setup and the guides you have been using. Even when I do establish connection quickly it still fails to update the time. Is there a way to force a refresh of the NTP? Sometimes I don't have connection to the gateway in under 120 seconds. I did a little google-fu and found that the router attempts to update the time at startup and again 120 seconds later, but no more after that. As of right now, it receives signal from the Wireless and I can access the internet on my laptop using a LAN cable through my router. I could go in to more detail if I need to. I should probably have noted sooner that I am using this router to receive WAN through wireless from a local "public" subscription based service. It still sits at startup original time, but adjusts to time zone changes if I adjust that, but never actually pulls the proper time. Okay, been playing with this for a bit now, and I still can't get NTP to play nice. Appreciate the initial assistance and will report back my results. I'll go apply the settings you suggest and give it another go. As far as my build, I thought I got it in my screenshots, but I guess I missed it:įirmware: DD-WRT v3.0-r44236 std (08/22/20) Sorry for wrong location, I was tired and read "Broadcom" as "Qualcom" for some reason. The old PIA instructions were better this is not good Just use the 2048 key certificate 4096 is overkillĭo not use the DNS server 10.0.0.242 (this could be the problem of NTP as this is a DNS server which is not publicly available.ĭo not use anything in the Additional config I see that they have updated their setup instructions: (well actually the first thing to do is to check if you have a decent build) If NTP is not working you have made a setup error so the first thing to do is to get that right.Įnable NTP leave the time server field blank, the DDWRT default should work and check your DNS server. You are posting in the wrong forum and you do not tell us what build you are using for all we know you are using the crappy build 40559 from the router database We can help you better if you follow the forum guide lines, link in my signature at the bottom of this post Last edited by Egotistical on Tue 21:26 edited 1 time in total I have been messing with this for a little over 3 days now and cannot even get a basic connection established with the PIA servers. Just to note: I followed the instructions I found on the PIA support website, as well as trying multiple fixes I found while scouring this website and a few others. Any assistance would be greatly appreciated: I have included screenshots and a pastebin of my log for reference. I have turned off the NTP setting and set the date/time manually through the command window as the NTP failed to pull the correct date and time, no matter how I configured it. I have not had any success up to this point. So, I have installed DD-WRT on a TP-Link AC1750 (Archer A7) and I am attempting to enable my Private Internet Access on the router. Posted: Sat 16:33 Post subject: -PIA DD-WRT issues ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |